Heavy Rains & Swimming Pools

Take these steps to protect your pool, or clean up after heavy rains.

Problem #1 – Too much Water in the Pool

Lower the water level in your pool to keep proper skimming action, and to avoid contamination from planters and deck area flooding.

For most pools with a sand/glass media or DE filter, the simplest way to lower the water level is to place the multiport valve onto the waste position and roll out the backwash hose. If you have a slide (push-pull) valve, backwash the filter to lower the water level.

Some pools have a hose spigot plumbed after the pump, or on the filter valve, which you can connect a garden hose, to lower water level. Or, you can use a submersible pump, aka pool cover pump, to keep the pool from overflowing.

Finally, there is the siphon method. A pool vacuum hose works best. Prime the hose in the pool, to fill it full of water, and attach a vac head or use a heavy item to hold the hose on the first or second step, the pool ladder, or swim out.

Cap the other end of the hose with your palm and quickly pull the hose away from the pool and a few feet below the level of the pool water. Uncap the hose at ground level and let it flow! Keep an eye on it though!

Problem #2 – Contaminants in the Pool!

From Run-Off: When a backyard pool gets 120 millimetres of rain in a few hours, flooding can result. If surrounding planters or lawns, or even concrete pool decks overflow into the pool, just a handful of soil or mulch can elevate phosphate levels and create problems with cloudy water and algae.

In severe cases, a pool can fill with a thick layer of silty mud, and all sorts of debris. Use leaf rakes to remove the big stuff, followed by a slow vacuum to waste. Follow-up with a good daily pool brush, and near continuous filtering. Clarifiers and flocculents can be used to speed up the process considerably, and may be needed for sand/glass media filters.

As the water clears, use a phosphate remover chemical to naturally consume phosphates in your pool. Just pour it into balanced pool water, run the filter for 24 hours, then backwash.

From the Rain: Rain is pure, distilled water, but as it falls through the air, it picks up dust, pollen, pollutants, oils, even algae spores. If you have tall trees overhanging the pool, rain will wash them clean, right into your pool, adding phosphates and other organic gunk. Add algaecide before a storm to help battle incoming invaders as they enter the pool.

Rain can also destroy your pool’s water balance. It dilutes the cyanuric acid, and can also soften the water, lowering calcium hardness, and it can affect pH and alkalinity as well. Acid Rain falling through smoggy summer air hits your pool at a very low pH, reducing pool pH and alkalinity. Be sure to test your water with a complete test kit.

Problem #3 – High Wind, Debris & Projectiles

Before a storm hits: Store all loose toys, furniture and cleaning equipment that could become airborne in high winds. Don’t cover the pool, which can be damaged severely in a heavy storm.

After a storm hits: Clean the pool, lower the water level, check the water balance and the chlorine level, adding sanitizer if needed. If your pool is a funky color, super-chlorinate with some pool shock, and run the filter overnight. It’s best to remove leaves and debris from the pool, and lower the pH to 7.2, before shocking the pool.

Problem #4 – Flooded Pool Equipment

Keep the filter running, however if flood waters threaten to submerge the pool pump, shut off power to the pool on the main home panel. If you can safely remove the pump, store it indoors, if the pump motor becomes submerged, it will likely need to be replaced.

Regular rain falling on your pool equipment will not usually cause any harm, even if it lasts for days on end. If concerned however, you can build a lean-to of some sort over your filter pump. Flooding however is the real problem. Sand bagging your pool equipment could save you from pump replacement, if flood waters rise above the equipment pad.

Problem #5 – Poor Water Drainage

If your pool has a tendency to flood in some areas of the pool deck, and if run-off from heavy rains ends up in the pool – it needs to be fixed. Pool decks should slope 6mm for every 300mm, and storm run-off needs to go somewhere; never in the pool.

Look at the way water moves around the pool, and rework the land to create natural swales, or install drains and drain pipes, or install French drains in gravel around the pool deck, sloped to a downhill, away from the pool location, and also away from the pool equipment.

[ Source: http://blog.intheswim.com/heavy-rains-swimming-pools ]

Leave a comment

Please note: comments must be approved before they are published.